Produkt-Liste> LED Lampen> Bi-Farben-LED-Lampen> 5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED
5mm Bi-Farben-Indikatorlampe IR + gelbe LED

5mm Bi-Farben-Indikatorlampe IR + gelbe LED

Holen Sie sich aktuelle Preis
    Schatten:
    • Zahlungsart: T/T,Paypal
    • Incoterm: FOB,EXW,FCA
    • Minimum der Bestellmenge: 5000 Piece/Pieces
    • Transport: Ocean,Land,Air
    • Hafen: SHENZHEN
    Lieferfähigkeit & Zusatzinformationen
    Additional Information

    VerpakungKartonschachtel

    Produktivität1000000000 pcs/week

    TransportOcean,Land,Air

    Ort Von ZukunftChina

    Unterstützung über7000000000 pcs/week

    Zertifikate GB/T19001-2008/ISO9001:2008

    HS-Code8541401000

    HafenSHENZHEN

    ZahlungsartT/T,Paypal

    IncotermFOB,EXW,FCA

    Produkteigenschaften

    Modell509FIRYGC

    MarkeBeste LED

    VersorgungsartOriginalhersteller

    ReferenzmaterialienDatenblatt

    HerkunftsortChina

    SpeziesLED

    PakettypDurch das Loch

    AnwendungElectronic Products

    Luminous IntensityHigh Directivity

    ColorIR And Yellow Green

    FormationGold Thread

    Inner PackingAnti-static Bag

    Current20mA

    Beam Width20 Degree

    PolarityCathode on short pin

    Wavelength880nm + 570nm (±10nm)

    Lens TypeClear lens

    Verpackung & Lieferung
    Verkaufseinheiten: Piece/Pieces
    Pakettyp: Kartonschachtel
    Herunterladen:

    The file is encrypted. Please fill in the following information to continue accessing it

    Unternehmensvideo
    Typ Durchsteck-LED als Rollenstreifen
    Produktbeschreibung

    How does a 2 color LED work?

    Bi-color LED can be package with SMD LED or through-hole LED Lamp type. In this 509FIRYGC, it's 5mm through-hole LED type with clear lens. Which can emits the full brightness from the LED chips. Then how does it work? Just following the datasheet and connect the correct polarity electric current, this LED will light up the color as you need. As the name, Bi-color LED lamps means that have two color inside one single LED package. We package yellow green color and IR LED (880nm LED) inside this LED Lamps case, which can make sure this 5mm bi-color LED can work good for status indicator and signage applications.

    509FIRYGC with Kingbright WP59SGSF4C T-1 34 (5mm) Bi-Color Indicator Lamp IR + Yellow green Through-hole LED


    Size of 5mm bi-color LED:

    Size of 509FIRYGC with Kingbright WP59SGSF4C T-1 34 (5mm) Bi-Color Indicator Lamp IR + Yellow green Through-hole LED

    *This size are also available in IR LED, UV LED, Red LED, Yellow LED, Green LED, Amber LED and Blue LED;*


    Electrical Optical Characteristics(Tc=25 )

    Parameter Symbol Min Type Max Unit Test condition
    Forward Volatge
    IR VF 1.3 1.4 1.6 V IF=20mA
    Green
    2.2 2.5 IF=20mA
    Luminous Intensity IR IV
    150
    250 mcd IF=20mA
    Green

    10 mw/sr IF=20mA
    Peak wavelength IR λP
    875 880 890 nm IF=20mA
    Green
    570 575
    Half width λ

    15
    nm IF=20mA
    Viewing half angle 2θ1/2
    20
    deg IF=20mA
    Reverse current IR

    5 uA VR=5V


    Production progress for through-hole LED:

    Production progress for through-hole LED


    Lagerbedingungen

    1. avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature;

    2. LEDs should be stored with temperature ≤30℃ and relative humidity<60%℃;

    3. Product in the original sealed package is recommended to be assembled within 72 hours of opening;

    4. Product in opened package for more than a week should be baked for 6-8 hours at 85-10℃;

    LED MOUNTING METHOD

    1, The lea d pitch of the LED must match the pitch of the mounting holes on the PCB during component placement ;

    Lead-forming may be required to insure the lead pitch matches the hole pitch ;

    Refer to the figure below for proper lead forming procedures ;

    Do not route PCB trace in the contact area between the leadframe and the PCB to prevent short-circuits ;

    1

    2. When soldering wires to the LED, each wire joint should be separately insulated with heat-shrink tube to prevent short-circuit contact.

    Do not bundle both wires in one heat shrink tube to avoid pinching the LED leads ;

    Pinching stress on the led leads may damage the internal structures and cause failure ;

    2

    3. Use stand-offs(Fig 3)or spacers(Fig 4)to securely position the LED above the PCB ;

    4. Maintain a minimum of 3mm cl earance between the base of the LED lens and the first lead bend (Fig. 5. Fig. 6)

    5.During lead forming, use tools or jigs to hold the leads securely so that the bending force will not be transmitted to the LED lens and its internal structures ;

    Do not perform lead forming once the component has been mounted onto the PCB ;

    3

    L ead Forming Procedures

    1. Lead Forming Procedures ;

    2 . Do not bend the leads more than twice (Fig. 7 );

    3. During soldering, component covers and holders should leave clearance to avoid placing damaging stress on the LED during soldering(Fig 8) ;

    4. The tip of the soldering iron should never touch the lens epoxy ;

    5. Through-hole LED s are incompatible with reflow soldering ;

    6. If the LED will undergo multiple soldering passes or face other processes where the part may be subjected to intense heat please check with Best LED for compatibility ;

    4



    In Kontakt kommen
    If you have any questions our products or services,feel free to reach out to us.Provide unique experiences for everyone involved with a brand.we’ve got preferential price and best-quality products for you.
    Please fill in the information
    * Please fill in your e-mail
    * Please fill in the content
    Produkt-Liste> LED Lampen> Bi-Farben-LED-Lampen> 5mm Bi-Farben-Indikatorlampe IR + gelbe LED
    Anfrage versenden
    *
    *

    We will contact you immediately

    Fill in more information so that we can get in touch with you faster

    Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

    senden